JUNIPER-MPLS-LDP-MIB DEFINITIONS ::= BEGIN

IMPORTS
    OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE,
    Integer32, Counter32, Unsigned32
        FROM SNMPv2-SMI
    MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
        FROM SNMPv2-CONF

    RowPointer, RowStatus, TimeInterval, TruthValue,
    TimeStamp, StorageType
        FROM SNMPv2-TC

    InterfaceIndex
        FROM IF-MIB

    InetAddressType,
    InetAddress,
    InetPortNumber
        FROM INET-ADDRESS-MIB
    
    jnxMibs 
        FROM JUNIPER-SMI

    MplsLabel,
    MplsLabelDistributionMethod,
    MplsLdpIdentifier,
    MplsLdpLabelType,
    MplsLspType,
    MplsLsrIdentifier,
    MplsRetentionMode

        FROM MPLS-TC-STD-MIB
    ;


jnxMplsLdpMIB MODULE-IDENTITY
    LAST-UPDATED "200605161200Z"  -- 16 May 2006 
    ORGANIZATION "Juniper Networks, Inc."
    CONTACT-INFO
            "    Juniper Technical Assistance Center
                     Juniper Networks, Inc.
                     1194 N. Mathilda Avenue
                     Sunnyvale, CA 94089
                     E-mail: support@juniper.net"

    DESCRIPTION
        "This MIB contains managed object definitions for the
        'Multiprotocol Label Switching, Label Distribution
        Protocol, LDP' document."

    REVISION "200605161200Z"  -- 16 May 2006
    DESCRIPTION
       "This mib was earlier supported on JUNOS as
        ldpmib.mib (MPLS-LDP-MIB)."

    ::= { jnxMibs 36 }


--****************************************************************

jnxMplsLdpObjects       OBJECT IDENTIFIER ::= { jnxMplsLdpMIB 1 }
jnxMplsLdpNotifications OBJECT IDENTIFIER ::= { jnxMplsLdpMIB 2 }
jnxMplsLdpConformance   OBJECT IDENTIFIER ::= { jnxMplsLdpMIB 3 }

--****************************************************************
-- MPLS LDP Objects
--****************************************************************

jnxMplsLdpLsrObjects    OBJECT IDENTIFIER ::= { jnxMplsLdpObjects 1 }

jnxMplsLdpEntityObjects OBJECT IDENTIFIER ::= { jnxMplsLdpObjects 2 }

--
-- The MPLS Label Distribution Protocol's
-- Label Switching Router Objects
--

jnxMplsLdpLsrId OBJECT-TYPE
    SYNTAX      MplsLsrIdentifier
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The LSR's Identifier."
    ::= { jnxMplsLdpLsrObjects 1 }

jnxMplsLdpLsrLoopDetectionCapable OBJECT-TYPE
    SYNTAX      INTEGER {
                           none(1),
                           other(2),
                           hopCount(3),
                           pathVector(4),

                           hopCountAndPathVector(5)
                        }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "A indication of whether this
        Label Switching Router supports
        loop detection.

        none(1) -- Loop Detection is not supported
                   on this LSR.

        other(2) -- Loop Detection is supported but
                    by a method other than those
                    listed below.

        hopCount(3) -- Loop Detection is supported by
                       Hop Count only.

        pathVector(4) -- Loop Detection is supported by
                        Path Vector only.

        hopCountAndPathVector(5) -- Loop Detection is
                             supported by both Hop Count
                             And Path Vector.

        Since Loop Detection is determined during
        Session Initialization, an individual session
        may not be running with loop detection.  This
        object simply gives an indication of whether or not the
        LSR has the ability to support Loop Detection and
        which types."
    ::= { jnxMplsLdpLsrObjects 2 }


--
-- The MPLS Label Distribution Protocol Entity Objects
--


jnxMplsLdpEntityLastChange OBJECT-TYPE
    SYNTAX  TimeStamp
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
        "The value of sysUpTime at the time of the most
        recent addition or deletion of an entry
        to the jnxMplsLdpEntityTable/jnxMplsLdpEntityStatsTable.

        If no such changes have occurred since the last

        re-initialization of the local management subsystem,
        then this object contains a zero value."
    ::= { jnxMplsLdpEntityObjects 1 }

jnxMplsLdpEntityIndexNext  OBJECT-TYPE
    SYNTAX      Unsigned32 (0..4294967295)
    MAX-ACCESS     read-only
    STATUS         current
    DESCRIPTION
        "This object contains an appropriate value to
        be used for jnxMplsLdpEntityIndex when creating
        entries in the jnxMplsLdpEntityTable. The value
        0 indicates that no unassigned entries are
        available. To obtain the jnxMplsLdpEntityIndex
        value for a new entry, the manager issues a
        management protocol retrieval operation to obtain
        the current value of this object.  After each
        retrieval, the agent should modify the value to
        the next unassigned index."
   ::= { jnxMplsLdpEntityObjects 2 }


jnxMplsLdpEntityTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF JnxMplsLdpEntityEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This table contains information about the
        MPLS Label Distribution Protocol Entities which
        exist on this Label Switching Router (LSR)."
    ::= { jnxMplsLdpEntityObjects 3 }

jnxMplsLdpEntityEntry OBJECT-TYPE
    SYNTAX      JnxMplsLdpEntityEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry in this table represents an LDP entity.
        An entry can be created by a network administrator
        or by an SNMP agent as instructed by LDP."
    INDEX       {  jnxMplsLdpEntityLdpId, jnxMplsLdpEntityIndex  }
    ::= { jnxMplsLdpEntityTable 1 }

JnxMplsLdpEntityEntry ::= SEQUENCE {
    jnxMplsLdpEntityLdpId              MplsLdpIdentifier,
    jnxMplsLdpEntityIndex              Unsigned32,
    jnxMplsLdpEntityProtocolVersion    Integer32,
    jnxMplsLdpEntityAdminStatus        INTEGER,
    jnxMplsLdpEntityOperStatus         INTEGER,
    jnxMplsLdpEntityTcpDscPort         InetPortNumber,

    jnxMplsLdpEntityUdpDscPort         InetPortNumber,
    jnxMplsLdpEntityMaxPduLength       Unsigned32,
    jnxMplsLdpEntityKeepAliveHoldTimer Integer32,
    jnxMplsLdpEntityHelloHoldTimer     Integer32,
    jnxMplsLdpEntityInitSesThreshold   Integer32,
    jnxMplsLdpEntityLabelDistMethod    MplsLabelDistributionMethod,
    jnxMplsLdpEntityLabelRetentionMode MplsRetentionMode,
    jnxMplsLdpEntityPathVectorLimit    Integer32,
    jnxMplsLdpEntityHopCountLimit      Integer32,
    jnxMplsLdpEntityTargetPeer         TruthValue,
    jnxMplsLdpEntityTargetPeerAddrType InetAddressType,
    jnxMplsLdpEntityTargetPeerAddr     InetAddress,
    jnxMplsLdpEntityLabelType          MplsLdpLabelType,
    jnxMplsLdpEntityDiscontinuityTime  TimeStamp,
    jnxMplsLdpEntityStorageType        StorageType,
    jnxMplsLdpEntityRowStatus          RowStatus
}


jnxMplsLdpEntityLdpId OBJECT-TYPE
    SYNTAX      MplsLdpIdentifier
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The LDP identifier."
    REFERENCE
        "[RFC3036] LDP Specification, Section on LDP Identifiers."
    ::= { jnxMplsLdpEntityEntry 1 }

jnxMplsLdpEntityIndex OBJECT-TYPE
    SYNTAX      Unsigned32 (1..4294967295)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This index is used as a secondary index to uniquely
        identify this row.  Before creating a row in this table,
        the 'jnxMplsLdpEntityIndexNext' object should be retrieved.
        That value should be used for the value of this index
        when creating a row in this table.  (NOTE:  if a value
        of zero (0) is retrieved, that indicates that no rows
        can be created in this table at this time.

        A secondary index (this object) is meaningful to some
        but not all, LDP implementations.  For example
        in an LDP implementation which uses PPP would
        use this index to differentiate PPP sub-links.

        Another way to use this index is to give this the
        value of ifIndex.  However, this is dependant
        on the implementation."

    ::= { jnxMplsLdpEntityEntry 2 }

jnxMplsLdpEntityProtocolVersion OBJECT-TYPE
    SYNTAX      Integer32(1..65535)
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The version number of the LDP protocol which will be
       used in the session initialization message.

       Section 3.5.3 in the LDP Specification specifies
       that the version of the LDP protocol is negotiated during
       session establishment. The value of this object
       represents the value that is sent in the initialization
       message."
    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.3 Initialization
       Message."
    DEFVAL { 1 }
    ::= { jnxMplsLdpEntityEntry 3 }

jnxMplsLdpEntityAdminStatus OBJECT-TYPE
    SYNTAX      INTEGER {
                  enable(1),
                  disable(2)
                }
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The administrative status of this LDP Entity.
        If this object is changed from 'enable' to 'disable'
        and this entity has already attempted to establish
        contact with a Peer, then all contact with that
        Peer is lost and all information from that Peer
        needs to be removed from the MIB. (This implies
        that the network management subsystem should clean
        up any related entry in the jnxMplsLdpPeerTable).

        At this point the user is able to change values
        which are related to this entity.

        When the admin status is set back to 'up', then
        this Entity will attempt to establish a new session
        with the Peer."
    DEFVAL  { enable }
    ::= { jnxMplsLdpEntityEntry 4 }


jnxMplsLdpEntityOperStatus OBJECT-TYPE
    SYNTAX      INTEGER {

                  unknown(1),
                  enabled(2),
                  disabled(3)
                }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The operational status of this LDP Entity."
    ::= { jnxMplsLdpEntityEntry 5 }

jnxMplsLdpEntityTcpDscPort OBJECT-TYPE
    SYNTAX      InetPortNumber
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The TCP Discovery Port for
        LDP.  The default value is the well-known
        value of this port."
    REFERENCE
        "[RFC3036], LDP Specification, Section 2.4.1,
        Basic Discovery Mechanism, Section 2.4.2,
        Extended Discovery Mechanism, Section
        3.10, Well-known Numbers, and Section 3.10.1.
        UDP and TCP Ports."
    DEFVAL { 646 }
    ::= { jnxMplsLdpEntityEntry 6 }

jnxMplsLdpEntityUdpDscPort OBJECT-TYPE
    SYNTAX      InetPortNumber
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The UDP Discovery Port for
        LDP.  The default value is the
        well-known value for this port."
    REFERENCE
        "[RFC3036], LDP Specification, Section 2.4.1,
        Basic Discovery Mechanism, Section 2.4.2,
        Extended Discovery Mechanism, Section
        3.10, Well-known Numbers, and Section 3.10.1.
        UDP and TCP Ports."
    DEFVAL { 646 }
    ::= { jnxMplsLdpEntityEntry 7 }

jnxMplsLdpEntityMaxPduLength OBJECT-TYPE
    SYNTAX      Unsigned32 (256..65535)
    UNITS       "octets"
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION

       "The maximum PDU Length that is sent in
       the Common Session Parameters of an Initialization
       Message. According to the LDP Specification [RFC3036]
       a value of 255 or less specifies the
       default maximum length of 4096 octets, this is why
       the value of this object starts at 256.  The operator
       should explicitely choose the default value (i.e. 4096),
       or some other value.

       The receiving LSR MUST calculate the maximum PDU
       length for the session by using the smaller of its and
       its peer's proposals for Max PDU Length."
    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.3.
       Initialization Message."
    DEFVAL { 4096 }
    ::= { jnxMplsLdpEntityEntry 8 }

jnxMplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE
    SYNTAX      Integer32 (1..65535)
    UNITS       "seconds"
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The 16-bit integer value which is the proposed keep
        alive hold timer for this LDP Entity."
    DEFVAL { 40 }
    ::= { jnxMplsLdpEntityEntry 9 }

jnxMplsLdpEntityHelloHoldTimer OBJECT-TYPE
    SYNTAX      Integer32 (0..65535)
    UNITS       "seconds"
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The 16-bit integer value which is the proposed Hello
        hold timer for this LDP Entity. The Hello Hold time
        in seconds.

        An LSR maintains a record of Hellos received
        from potential peers.  This object represents
        the Hold Time in the Common Hello Parameters TLV of
        the Hello Message.

        A value of 0 is a default value and should be
        interpretted in conjunction with the
        jnxMplsLdpEntityTargetPeer object.

        If the value of this object is 0: if the value of the
        jnxMplsLdpEntityTargetPeer object is false(2), then this

        specifies that the Hold Time's actual default value is
        15 seconds (i.e. the default Hold time for Link Hellos
        is 15 seconds).  Otherwise if the value of the
        jnxMplsLdpEntityTargetPeer object is true(1), then this
        specifies that the Hold Time's actual default value is
        45 seconds (i.e. the default Hold time for Targeted
        Hellos is 45 seconds).

        A value of 65535 means infinite (i.e. wait forever).

        All other values represent the amount of time in
        seconds to wait for a Hello Message.  Setting the
        hold time to a value smaller than 15 is not
        recommended, although not forbidden according
        to [RFC3036]."
    REFERENCE
        "[RFC3036], LDP Specification, Section 3.5.2.,
        Hello Message."
    DEFVAL { 0 }
    ::= { jnxMplsLdpEntityEntry 10 }

jnxMplsLdpEntityInitSesThreshold OBJECT-TYPE
    SYNTAX      Integer32(0..100)
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "When attempting to establish a session with a
        given Peer, the given LDP Entity should
        send out the SNMP notification,
        'jnxMplsLdpInitSesThresholdExceeded', when
        the number of Session Initialization messages sent
        exceeds this threshold.  The notification is
        used to notify an operator when this Entity and
        its Peer are possibily engaged in an endless
        sequence of messages as each NAKs the other's
        Initialization messages with Error Notification
        messages.  Setting this threshold which triggers
        the notification is one way to
        notify the operator.

        A value of 0 (zero) for this object
        indicates that the threshold is infinity, thus
        the SNMP notification will never be generated."
    REFERENCE
        "[RFC3036], LDP Specification,
        Section 2.5.3 Session Initialization."
    DEFVAL { 8 }
    ::= { jnxMplsLdpEntityEntry 11 }


jnxMplsLdpEntityLabelDistMethod OBJECT-TYPE
    SYNTAX      MplsLabelDistributionMethod
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "For any given LDP session, the method of
        label distribution must be specified."
    ::= { jnxMplsLdpEntityEntry 12 }

jnxMplsLdpEntityLabelRetentionMode OBJECT-TYPE
    SYNTAX      MplsRetentionMode
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The LDP Entity can be configured to use either
        conservative or liberal label retention mode.

        If the value of this object is conservative(1)
        then advertized label mappings are retained
        only if they will be used to forward packets,
        i.e. if label came from a valid next hop.

        If the value of this object is liberal(2)
        then all advertized label mappings are retained
        whether they are from a valid next hop or not."
    ::= { jnxMplsLdpEntityEntry 13 }

jnxMplsLdpEntityPathVectorLimit OBJECT-TYPE
    SYNTAX      Integer32 (0..255)
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "If the value of this object is 0 (zero) then
        Loop Dection for Path Vectors is disabled.

        Otherwise, if this object has a value greater than
        zero, then Loop Dection for Path Vectors is enabled,
        and the Path Vector Limit is this value.
        Also, the value of the object,
        'jnxMplsLdpLsrLoopDetectionCapable', must be set to
        either 'pathVector(4)' or 'hopCountAndPathVector(5)',
        if this object has a value greater than 0 (zero),
        otherwise it is ignored."
    REFERENCE
       "[RFC3036], LDP Specification, Section 2.8 Loop Dection,
       Section 3.4.5 Path Vector TLV."
    ::= { jnxMplsLdpEntityEntry 14 }

jnxMplsLdpEntityHopCountLimit OBJECT-TYPE
    SYNTAX       Integer32 (0..255)

--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS       current
    DESCRIPTION
        "If the value of this object is 0 (zero),
        then Loop Detection using Hop Counters is
        disabled.

        If the value of this object is greater than
        0 (zero) then Loop Detection using Hop
        Counters is enabled, and this object
        specifies this Entity's maximum allowable
        value for the Hop Count.
        Also, the value of the object
        jnxMplsLdpLsrLoopDetectionCapable must be set
        to either 'hopCount(3)' or
        'hopCountAndPathVector(5)' if this object
        has a value greater than 0 (zero), otherwise
        it is ignored."
    DEFVAL { 0 }
    ::= { jnxMplsLdpEntityEntry 15 }

jnxMplsLdpEntityTargetPeer OBJECT-TYPE
    SYNTAX      TruthValue
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "If this LDP entity uses targeted peer then set
        this to true."
    DEFVAL { false }
    ::= { jnxMplsLdpEntityEntry 16 }

jnxMplsLdpEntityTargetPeerAddrType OBJECT-TYPE
    SYNTAX      InetAddressType
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The type of the internetwork layer address used for
        the Extended Discovery. This object indicates how
        the value of jnxMplsLdpEntityTargetPeerAddr is to
        be interpreted."
    ::= { jnxMplsLdpEntityEntry 17 }

jnxMplsLdpEntityTargetPeerAddr OBJECT-TYPE
    SYNTAX      InetAddress
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of the internetwork layer address used for
        the Extended Discovery."
   ::= { jnxMplsLdpEntityEntry 18 }

jnxMplsLdpEntityLabelType OBJECT-TYPE
    SYNTAX      MplsLdpLabelType
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "Specifies the optional parameters for the LDP
        Initialization Message.  If the value is generic(1)
        then no optional parameters will be sent in
        the LDP Initialization message associated with
        this Entity.

        If the value is atmParameters(2) then
        a row must be created in the jnxMplsLdpEntityAtmParms
        Table, which corresponds to this entry.

        If the value is frameRelayParameters(3) then
        a row must be created in the jnxMplsLdpEntityFrameRelayParms
        Table, which corresponds to this entry."
    REFERENCE
        "[RFC3036], LDP Specification, Section 3.5.3.,
        Initialization Message."
    ::= { jnxMplsLdpEntityEntry 19 }


jnxMplsLdpEntityDiscontinuityTime OBJECT-TYPE
    SYNTAX      TimeStamp
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of sysUpTime on the most recent occasion
        at which any one or more of this entity's counters
        suffered a discontinuity.  The relevant counters are the
        specific instances associated with this entity of
        any Counter32, or Counter64 object contained
        in the 'jnxMplsLdpEntityStatsTable'.  If no such
        discontinuities have occurred since the last
        re-initialization of the local management
        subsystem, then this object contains a zero
        value."
    ::= { jnxMplsLdpEntityEntry 20 }

jnxMplsLdpEntityStorageType  OBJECT-TYPE
    SYNTAX      StorageType
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
             "The storage type for this entry."
    ::= { jnxMplsLdpEntityEntry 21 }

jnxMplsLdpEntityRowStatus OBJECT-TYPE

    SYNTAX      RowStatus
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "An object that allows entries in this table to
         be created and deleted using the
         RowStatus convention."
    ::= { jnxMplsLdpEntityEntry 22 }


--
-- The MPLS LDP Entity Statistics Table
--

jnxMplsLdpEntityStatsTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF JnxMplsLdpEntityStatsEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This table is a read-only table which augments
        the jnxMplsLdpEntityTable.  The purpose of this
        table is to keep statistical information about
        the LDP Entities on the LSR."
    ::= { jnxMplsLdpEntityObjects 4 }

jnxMplsLdpEntityStatsEntry OBJECT-TYPE
    SYNTAX      JnxMplsLdpEntityStatsEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A row in this table contains statistical information
        about an LDP Entity.  Some counters contained in a
        row are for fatal errors received during a former
        LDP Session associated with this entry.  For example,
        an Ldp Pdu received on a TCP connection during an
        LDP Session contains a fatal error.  That
        error is counted here, because the
        session is terminated.

        If the error is NOT fatal (i.e. and the Session
        remains), then the error is counted in the
        jnxMplsLdpSesStatsEntry."
    AUGMENTS       {   jnxMplsLdpEntityEntry  }
    ::= { jnxMplsLdpEntityStatsTable 1 }

JnxMplsLdpEntityStatsEntry ::= SEQUENCE {
    jnxMplsLdpAttemptedSessions            Counter32,
    jnxMplsLdpSesRejectedNoHelloErrors     Counter32,
    jnxMplsLdpSesRejectedAdErrors          Counter32,
    jnxMplsLdpSesRejectedMaxPduErrors      Counter32,

    jnxMplsLdpSesRejectedLRErrors          Counter32,
    jnxMplsLdpBadLdpIdentifierErrors       Counter32,
    jnxMplsLdpBadPduLengthErrors           Counter32,
    jnxMplsLdpBadMessageLengthErrors       Counter32,
    jnxMplsLdpBadTlvLengthErrors           Counter32,
    jnxMplsLdpMalformedTlvValueErrors      Counter32,
    jnxMplsLdpKeepAliveTimerExpErrors      Counter32,
    jnxMplsLdpShutdownNotifReceived        Counter32,
    jnxMplsLdpShutdownNotifSent            Counter32
}

jnxMplsLdpAttemptedSessions OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "A count of the total attempted sessions for
        this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    ::= { jnxMplsLdpEntityStatsEntry 1 }


jnxMplsLdpSesRejectedNoHelloErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "A count of the Session Rejected/No Hello Error
        Notification Messages sent or received by
        this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    ::= { jnxMplsLdpEntityStatsEntry 2 }

jnxMplsLdpSesRejectedAdErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "A count of the Session Rejected/Parameters
        Advertisement Mode Error Notification Messages sent
        or received by this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    ::= { jnxMplsLdpEntityStatsEntry 3 }

jnxMplsLdpSesRejectedMaxPduErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "A count of the Session Rejected/Parameters
        Max Pdu Length Error Notification Messages sent
        or received by this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    ::= { jnxMplsLdpEntityStatsEntry 4 }

jnxMplsLdpSesRejectedLRErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "A count of the Session Rejected/Parameters
        Label Range Notification Messages sent
        or received by this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    ::= { jnxMplsLdpEntityStatsEntry 5 }


jnxMplsLdpBadLdpIdentifierErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Bad LDP Identifier
        Fatal Errors detected by the session(s)
        (past and present) associated with this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."

    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.1.2."
    ::= { jnxMplsLdpEntityStatsEntry 6 }

jnxMplsLdpBadPduLengthErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Bad Pdu Length
        Fatal Errors detected by the session(s)
        (past and present) associated with this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.1.2."
    ::= { jnxMplsLdpEntityStatsEntry 7 }

jnxMplsLdpBadMessageLengthErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Bad Message
        Length Fatal Errors detected by the session(s)
        (past and present) associated with this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.1.2."
    ::= { jnxMplsLdpEntityStatsEntry 8 }

jnxMplsLdpBadTlvLengthErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Bad TLV
        Length Fatal Errors detected by the session(s)
        (past and present) associated with this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of

        jnxMplsLdpEntityDiscontinuityTime."
    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.1.2."
    ::= { jnxMplsLdpEntityStatsEntry 9 }

jnxMplsLdpMalformedTlvValueErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Malformed TLV
        Value Fatal Errors detected by the session(s)
        (past and present) associated with this
        LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.1.2."
    ::= { jnxMplsLdpEntityStatsEntry 10 }

jnxMplsLdpKeepAliveTimerExpErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Session Keep Alive
        Timer Expired Errors detected by the session(s)
        (past and present) associated with this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.1.2."
    ::= { jnxMplsLdpEntityStatsEntry 11 }

jnxMplsLdpShutdownNotifReceived OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Shutdown Notfications
        received related to session(s) (past and present)
        associated with this LDP Entity.

        Discontinuities in the value of this counter can occur

        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    ::= { jnxMplsLdpEntityStatsEntry 12 }

jnxMplsLdpShutdownNotifSent OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Shutdown Notfications
        sent related to session(s) (past and present) associated
        with this LDP Entity.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpEntityDiscontinuityTime."
    ::= { jnxMplsLdpEntityStatsEntry 13 }


--
-- The MPLS LDP Peer Table
--

jnxMplsLdpSessionObjects OBJECT IDENTIFIER ::=
                                         { jnxMplsLdpObjects 3 }


jnxMplsLdpPeerLastChange OBJECT-TYPE
    SYNTAX  TimeStamp
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
        "The value of sysUpTime at the time of the most
        recent addition or deletion to the
        jnxMplsLdpPeerTable/jnxMplsLdpSessionTable."
    ::= { jnxMplsLdpSessionObjects 1 }

jnxMplsLdpPeerTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF JnxMplsLdpPeerEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "Information about LDP peers known by Entities in
        the jnxMplsLdpEntityTable.  The information in this table
        is based on information from the Entity-Peer interaction
        during session initialization but is not appropriate
        for the jnxMplsLdpSessionTable, because objects in this
        table may or may not be used in session establishment."

    ::= { jnxMplsLdpSessionObjects 2 }

jnxMplsLdpPeerEntry OBJECT-TYPE
    SYNTAX      JnxMplsLdpPeerEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "Information about a single Peer which is related
        to a Session.  NOTE:  this table is augmented by
        the jnxMplsLdpSessionTable."
    INDEX       { jnxMplsLdpEntityLdpId,
                  jnxMplsLdpEntityIndex,
                  jnxMplsLdpPeerLdpId }
    ::= { jnxMplsLdpPeerTable 1 }

JnxMplsLdpPeerEntry ::= SEQUENCE {
    jnxMplsLdpPeerLdpId                MplsLdpIdentifier,
    jnxMplsLdpPeerLabelDistMethod      MplsLabelDistributionMethod,
    jnxMplsLdpPeerPathVectorLimit      Integer32
}

jnxMplsLdpPeerLdpId OBJECT-TYPE
    SYNTAX      MplsLdpIdentifier
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The LDP identifier of this LDP Peer."
    ::= { jnxMplsLdpPeerEntry 1 }

jnxMplsLdpPeerLabelDistMethod OBJECT-TYPE
    SYNTAX      MplsLabelDistributionMethod
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "For any given LDP session, the method of
        label distribution must be specified."
    ::= { jnxMplsLdpPeerEntry 2 }

jnxMplsLdpPeerPathVectorLimit OBJECT-TYPE
    SYNTAX      Integer32 (0..255)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "If the value of this object is 0 (zero) then
        Loop Dection for Path Vectors for this Peer
        is disabled.

        Otherwise, if this object has a value greater than
        zero, then Loop Dection for Path  Vectors for this
        Peer is enabled and the Path Vector Limit is this value."

    REFERENCE
       "[RFC3036], LDP Specification, Section 2.8 Loop Dection,
       Section 3.4.5 Path Vector TLV."
    ::= { jnxMplsLdpPeerEntry 3 }


--
-- The MPLS LDP Sessions Table
--

jnxMplsLdpSessionTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF JnxMplsLdpSessionEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table of Sessions between the LDP Entities and
        LDP Peers.  Each row represents a single session."
    ::= { jnxMplsLdpSessionObjects 3 }

jnxMplsLdpSessionEntry OBJECT-TYPE
    SYNTAX      JnxMplsLdpSessionEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry in this table represents information on a
        single session between an LDP Entity and LDP Peer.
        The information contained in a row is read-only.

        Please note:  the Path Vector Limit for the
        Session is the value which is configured in
        the corresponding jnxMplsLdpEntityEntry. The
        Peer's Path Vector Limit is in noted in the
        jnxMplsLdpPeerTable.

        Values which may differ from those configured are
        noted in the objects of this table, the
        jnxMplsLdpAtmSesTable and the
        jnxMplsLdpFrameRelaySesTable. A value will
        differ if it was negotiated between the
        Entity and the Peer. Values may or may not
        be negotiated. For example, if the values
        are the same then no negotiation takes place.
        If they are negotiated, then they may differ."
    AUGMENTS { jnxMplsLdpPeerEntry }
    ::= { jnxMplsLdpSessionTable 1 }

JnxMplsLdpSessionEntry ::= SEQUENCE {
    jnxMplsLdpSesStateLastChange       TimeStamp,
    jnxMplsLdpSesState                 INTEGER,
    jnxMplsLdpSesProtocolVersion       Integer32,

    jnxMplsLdpSesKeepAliveHoldTimeRem  TimeInterval,
    jnxMplsLdpSesMaxPduLength          Unsigned32,
    jnxMplsLdpSesDiscontinuityTime     TimeStamp
}

jnxMplsLdpSesStateLastChange OBJECT-TYPE
    SYNTAX TimeStamp
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of this object is sysUpTime when the
        most recent change in the jnxMplsLdpSesState
        object occurred.  When the entry is created, then
        this object has the value of sysUpTime when the
        entry was created."
    ::= { jnxMplsLdpSessionEntry 1 }

jnxMplsLdpSesState OBJECT-TYPE
    SYNTAX      INTEGER {
                   nonexistent(1),
                   initialized(2),
                   openrec(3),
                   opensent(4),
                   operational(5)
                }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The current state of the session, all of the
        states 1 to 5 are based on the state machine for
        session negotiation behavior."
    REFERENCE
        "[RFC3036], LDP Specification, Section 2.5.4,
        Initialization State Machine."
    ::= { jnxMplsLdpSessionEntry 2 }

jnxMplsLdpSesProtocolVersion OBJECT-TYPE
    SYNTAX      Integer32(1..65535)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The version of the LDP Protocol which
        this session is using.  This is the version of
        the LDP protocol which has been negotiated during
        session initialization."
    REFERENCE
       "[RFC3036], LDP Specification, Section 3.5.3,
       Initialization Message."
    ::= { jnxMplsLdpSessionEntry 3 }

jnxMplsLdpSesKeepAliveHoldTimeRem OBJECT-TYPE
    SYNTAX      TimeInterval
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The keep alive hold time remaining for this session."
    ::= { jnxMplsLdpSessionEntry 4 }

jnxMplsLdpSesMaxPduLength OBJECT-TYPE
    SYNTAX      Unsigned32 (1..65535)
    UNITS       "octets"
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of maximum allowable length for LDP PDUs for
        this session.  This value may have been negotiated during
        the Session Initialization.  This object is related to
        the jnxMplsLdpEntityMaxPduLength object.  The
        jnxMplsLdpEntityMaxPduLength object specifies the requested
        LDP PDU length, and this object reflects the negotiated
        LDP PDU length between the Entity and
        the Peer."
    ::= { jnxMplsLdpSessionEntry 5 }

jnxMplsLdpSesDiscontinuityTime OBJECT-TYPE
    SYNTAX      TimeStamp
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of sysUpTime on the most recent occasion at
        which any one or more of this session's counters
        suffered a discontinuity.  The relevant counters are
        the specific instances associated with this session
        of any Counter32 or Counter64 object contained in the
        jnxMplsLdpSessionStatsTable.

        The initial value of this object is the value of
        sysUpTime when the entry was created in this table.

        Also, a command generator can distinguish when a session
        between a given Entity and Peer goes away and then is
        're-established'.  This value would change and
        thus indicate to the command generator that this is a
        different session."
    ::= { jnxMplsLdpSessionEntry 6 }


--
-- The MPLS LDP Session Statistics Table
--

jnxMplsLdpSesStatsTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF JnxMplsLdpSesStatsEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table of statistics for Sessions between
        LDP Entities and LDP Peers."
    ::= { jnxMplsLdpSessionObjects 4 }

jnxMplsLdpSesStatsEntry OBJECT-TYPE
    SYNTAX      JnxMplsLdpSesStatsEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry in this table represents statistical
        information on a single session between an LDP
        Entity and LDP Peer."
    AUGMENTS       { jnxMplsLdpPeerEntry }
    ::= { jnxMplsLdpSesStatsTable 1 }

JnxMplsLdpSesStatsEntry ::= SEQUENCE {
    jnxMplsLdpSesStatsUnkMesTypeErrors Counter32,
    jnxMplsLdpSesStatsUnkTlvErrors         Counter32
}

jnxMplsLdpSesStatsUnkMesTypeErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Unknown Message Type
        Errors detected during this session.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of
        jnxMplsLdpSesDiscontinuityTime."
    ::= { jnxMplsLdpSesStatsEntry 1 }

jnxMplsLdpSesStatsUnkTlvErrors OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object counts the number of Unknown TLV Errors
        detected during this session.

        Discontinuities in the value of this counter can occur
        at re-initialization of the management system, and at
        other times as indicated by the value of

        jnxMplsLdpSessionDiscontinuityTime."
    ::= { jnxMplsLdpSesStatsEntry 2 }


--
-- The MPLS LDP Hello Adjacency Table
--

jnxMplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::=
                              { jnxMplsLdpSessionObjects 5 }

jnxMplsLdpHelloAdjacencyTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF JnxMplsLdpHelloAdjacencyEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table of Hello Adjacencies for Sessions."
    ::= { jnxMplsLdpHelloAdjacencyObjects 1 }

jnxMplsLdpHelloAdjacencyEntry OBJECT-TYPE
    SYNTAX      JnxMplsLdpHelloAdjacencyEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "Each row represents a single LDP Hello Adjacency.
        An LDP Session can have one or more Hello adjacencies."
         INDEX       { jnxMplsLdpEntityLdpId,
                       jnxMplsLdpEntityIndex,
                       jnxMplsLdpPeerLdpId,
                       jnxMplsLdpHelloAdjIndex }
    ::= { jnxMplsLdpHelloAdjacencyTable 1 }

JnxMplsLdpHelloAdjacencyEntry ::= SEQUENCE {
    jnxMplsLdpHelloAdjIndex         Unsigned32,
    jnxMplsLdpHelloAdjHoldTimeRem   TimeInterval,
    jnxMplsLdpHelloAdjType          INTEGER
}

jnxMplsLdpHelloAdjIndex OBJECT-TYPE
    SYNTAX      Unsigned32 (1..4294967295)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An identifier for this specific adjacency."
    ::= { jnxMplsLdpHelloAdjacencyEntry 1 }

jnxMplsLdpHelloAdjHoldTimeRem OBJECT-TYPE
    SYNTAX      TimeInterval
    MAX-ACCESS  read-only
    STATUS      current

    DESCRIPTION
        "The time remaining for this Hello Adjacency.
        This interval will change when the 'next'
        Hello message which corresponds to this
        Hello Adjacency is received."
    ::= { jnxMplsLdpHelloAdjacencyEntry 2 }

jnxMplsLdpHelloAdjType OBJECT-TYPE
    SYNTAX      INTEGER {
                   link(1),
                   targeted(2)
                }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This adjacency is the result of a 'link'
        hello if the value of this object is link(1).
        Otherwise, it is a result of a 'targeted'
        hello, targeted(2)."
    ::= { jnxMplsLdpHelloAdjacencyEntry 3 }


--
--  Session Label (LSP) Mapping to LSR MIB's LIB Information.
--

jnxMplsLdpLspTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF JnxMplsLdpLspEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table of LDP LSP's which
        map to a Segment Table in the
        the LSR MIB's (either the mplsInSegmentTable
        or mplsOutSegmentTable) AND to the
        LSR MIB's mplsXCTable."
    ::= { jnxMplsLdpSessionObjects 6 }

jnxMplsLdpLspEntry OBJECT-TYPE
    SYNTAX      JnxMplsLdpLspEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry in this table represents information on a
        single LDP LSP which is represented by
        a session's index triple (jnxMplsLdpEntityLdpId,
        jnxMplsLdpEntityIndex, jnxMplsLdpPeerLdpId) AND the
        index tuple (jnxMplsLdpLspIfIndex, jnxMplsLdpLspLabel).

        The information contained in a row is read-only."

    INDEX       { jnxMplsLdpEntityLdpId,
                  jnxMplsLdpEntityIndex,
                  jnxMplsLdpPeerLdpId,
                  jnxMplsLdpLspIfIndex,
                  jnxMplsLdpLspLabel
                }
    ::= { jnxMplsLdpLspTable 1 }

JnxMplsLdpLspEntry ::= SEQUENCE {
    jnxMplsLdpLspIfIndex               InterfaceIndex,
    jnxMplsLdpLspLabel                 MplsLabel,
    jnxMplsLdpLspLabelType             MplsLdpLabelType,
    jnxMplsLdpLspType                  MplsLspType,
    jnxMplsLdpLspLsrInSegmentPointer   RowPointer,
    jnxMplsLdpLspLsrOutSegmentPointer  RowPointer,
    jnxMplsLdpLspLsrXCPointer          RowPointer
}

jnxMplsLdpLspIfIndex OBJECT-TYPE
    SYNTAX       InterfaceIndex
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
        "The ifIndex value associated with this LSP."
    ::= { jnxMplsLdpLspEntry 1 }

jnxMplsLdpLspLabel OBJECT-TYPE
    SYNTAX        MplsLabel
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
        "The LDP label for this LSP."
    ::= { jnxMplsLdpLspEntry 2 }

jnxMplsLdpLspLabelType  OBJECT-TYPE
    SYNTAX        MplsLdpLabelType
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "The Layer 2 Label Type."
    ::= { jnxMplsLdpLspEntry 3 }

jnxMplsLdpLspType OBJECT-TYPE
    SYNTAX        MplsLspType
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
        "The type of LSP connection.
        The possible values are:

           unknown(1)         --  if the LSP is not known
                                  to be one of the following.

          terminatingLsp(2)   -- if the LSP terminates
                                 on the LSR, then this
                                 is an ingressing LSP
                                 which ends on the LSR,

          originatingLsp(3)   -- if the LSP originates
                                 from the LSR, then this
                                 is an egressing LSP which is
                                 the head-end of the LSP,

        crossConnectingLsp(4) -- if the LSP ingresses
                                 and egresses on the LSR,
                                 then it is cross-connecting
                                 on that LSR."
    ::= { jnxMplsLdpLspEntry 4 }

jnxMplsLdpLspLsrInSegmentPointer OBJECT-TYPE
    SYNTAX      RowPointer
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "If this LSP terminates or is cross-connecting
        on this LSR, then this RowPointer should point
        to an instance of an object in the
        mplsLsrInSegmentTable. In other words if
        the value of jnxMplsLdpLspType is
        terminatingLsp(2) or crossConnectingLsp(4),
        then this should point to an instance of an object
        in the LSR-MIB's mplsInSegmentTable.

        Otherwise, a value of zeroDotzero indicates that
        this LSP has no corresponding mplsInSegmentEntry."
    ::= { jnxMplsLdpLspEntry 5 }

jnxMplsLdpLspLsrOutSegmentPointer OBJECT-TYPE
    SYNTAX      RowPointer
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "If this LSP originates or is cross-connecting
        on this LSR, then this RowPointer should point
        to an instance of an object in the LSR-MIB's
        mplsOutSegmentTable. In other words if
        the value of jnxMplsLdpLspType is
        originatingLsp(3) or crossConnectingLsp(4),
        then this should point to an instance of an object
        in the LSR-MIB's mplsOutSegmentTable.

        Otherwise, a value of zeroDotzero indicates that
        this LSP has no corresponding mplsOutSegmentEntry."
    ::= { jnxMplsLdpLspEntry 6 }

jnxMplsLdpLspLsrXCPointer OBJECT-TYPE
    SYNTAX      RowPointer
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "If this LSP is cross-connecting on this LSR,
        then this RowPointer should point
        to an instance of an object in the
        LSR-MIB's mplsXCTable. In other words if
        the value of jnxMplsLdpLspType is crossConnectingLsp(4),
        then this should point to an instance of an object
        in the LSR-MIB's mplsXCTable.

        Otherwise, a value of zeroDotzero indicates that
        this LSP has no corresponding mplsXCEntry."
    ::= { jnxMplsLdpLspEntry 7 }


--
-- Mpls FEC Table
--

jnxMplsFecObjects OBJECT IDENTIFIER ::=
                                      { jnxMplsLdpSessionObjects 7 }

jnxMplsFecIndexNext  OBJECT-TYPE
    SYNTAX      Unsigned32 (0..4294967295)
    MAX-ACCESS     read-only
    STATUS         current
    DESCRIPTION
        "This object contains an appropriate value to
        be used for jnxMplsFecIndex when creating
        entries in the jnxMplsFecTable. The value
        0 indicates that no unassigned entries are
        available. To obtain the jnxMplsFecIndex
        value for a new entry, the manager issues a
        management protocol retrieval operation to obtain
        the current value of this object.  After each
        retrieval, the agent should modify the value to
        the next unassigned index."
   ::= { jnxMplsFecObjects 1 }


jnxMplsFecTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF JnxMplsFecEntry
    MAX-ACCESS  not-accessible

    STATUS      current
    DESCRIPTION
        "This table represents the FEC
        (Forwarding Equivalence Class)
        Information associated with an LSP."
    ::= { jnxMplsFecObjects 2 }

jnxMplsFecEntry OBJECT-TYPE
    SYNTAX      JnxMplsFecEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "Each row represents a single FEC Element."
    INDEX       { jnxMplsFecIndex }
    ::= { jnxMplsFecTable 1 }

JnxMplsFecEntry ::= SEQUENCE {
    jnxMplsFecIndex         Unsigned32,
    jnxMplsFecType          INTEGER,
    jnxMplsFecAddrLength    Integer32,
    jnxMplsFecAddrFamily    InetAddressType,
    jnxMplsFecAddr          InetAddress,
    jnxMplsFecStorageType   StorageType,
    jnxMplsFecRowStatus     RowStatus
}

jnxMplsFecIndex OBJECT-TYPE
    SYNTAX      Unsigned32(1..4294967295)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The index which uniquely identifies this entry."
    ::= { jnxMplsFecEntry 1 }

jnxMplsFecType  OBJECT-TYPE
    SYNTAX      INTEGER {
                   prefix(1),
                   hostAddress(2)
                }
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only    
    STATUS      current
    DESCRIPTION
        "The type of the FEC.  If the value of this object
        is 'prefix(1)' then the FEC type described by this
        row is for address prefixes.

        If the value of this object is 'hostAddress(2)' then
        the FEC type described by this row is a host address."
    ::= { jnxMplsFecEntry 2 }

jnxMplsFecAddrLength  OBJECT-TYPE
    SYNTAX      Integer32(0..255)
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "If the value of 'jnxMplsFecType' is 'prefix(1)'
        then the value of this object is the length in
        bits of the address prefix represented by
        'jnxMplsFecAddr', or if the length is zero then
        this is a special value which indicates that the
        prefix matches all addresses.  In this case the
        prefix is also zero (i.e. 'jnxMplsFecAddr' will
        have the value of zero.)"
    DEFVAL { 0 }
    ::= { jnxMplsFecEntry 3 }

jnxMplsFecAddrFamily  OBJECT-TYPE
    SYNTAX      InetAddressType
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of this object is from the Address Family
        Numbers."
    ::= { jnxMplsFecEntry 4 }


jnxMplsFecAddr     OBJECT-TYPE
    SYNTAX      InetAddress
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "If the value of 'jnxMplsFecType' is 'prefix(1)'
        then the value of this object is the address prefix.
        If the value of the 'jnxMplsFecAddrLength'
        is object is zero, then this object should also be
        zero.

        If the value of the 'jnxMplsFecType' is 'hostAddress(2)'
        then this is the host address."
    ::= { jnxMplsFecEntry 5 }

jnxMplsFecStorageType  OBJECT-TYPE
    SYNTAX      StorageType
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
             "The storage type for this entry."
    ::= { jnxMplsFecEntry 6 }

jnxMplsFecRowStatus OBJECT-TYPE

    SYNTAX      RowStatus
--  MAX-ACCESS  read-create
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "An object that allows entries in this table to
         be created and deleted using the
         RowStatus convention."
    ::= { jnxMplsFecEntry 7 }


--
--  LDP LSP FEC Table
--

jnxMplsLdpLspFecTable OBJECT-TYPE
   SYNTAX      SEQUENCE OF JnxMplsLdpLspFecEntry
   MAX-ACCESS  not-accessible
   STATUS      current
   DESCRIPTION
      "A table which shows the relationship between
      LDP LSP's and FECs.  Each row represents
      a single LSP to FEC association.
      This table is read-only."
  ::= { jnxMplsLdpSessionObjects 8 }

jnxMplsLdpLspFecEntry OBJECT-TYPE
   SYNTAX     JnxMplsLdpLspFecEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An entry represents a LDP LSP
      to FEC association."
   INDEX       { jnxMplsLdpEntityLdpId,
                 jnxMplsLdpEntityIndex,
                 jnxMplsLdpPeerLdpId,
                 jnxMplsLdpLspIfIndex,
                 jnxMplsLdpLspLabel,
                 jnxMplsFecIndex
                }
   ::= { jnxMplsLdpLspFecTable 1 }

JnxMplsLdpLspFecEntry ::= SEQUENCE {
   jnxMplsLdpLspFecOperStatus   INTEGER,
   jnxMplsLdpLspFecLastChange   TimeStamp,
   jnxMplsLdpLspFecRowStatus    RowStatus
}

jnxMplsLdpLspFecOperStatus  OBJECT-TYPE
   SYNTAX      INTEGER {
                         unknown(1),

                         inUse(2),
                         notInUse(3)
                       }
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
      "An indication of the operational status of
      the FEC associated with LDP LSP.

      unknown(1) - this is a temporary state which
                   may indicate the LSP-FEC association
                   is in a state of transition.

      inUse(2) - the FEC associated with the LSP is
                 currently being applied.

      notInUse(3) - the FEC associated with the LSP is
                    not being applied.  Eventually, this
                    entry may be aged out."
   ::= { jnxMplsLdpLspFecEntry 1 }

jnxMplsLdpLspFecLastChange  OBJECT-TYPE
   SYNTAX     TimeStamp
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "This value of sysUpTime when the
      jnxMplsLdpLspFecOperStatus last changed state."
   ::= { jnxMplsLdpLspFecEntry 2 }

jnxMplsLdpLspFecRowStatus  OBJECT-TYPE
   SYNTAX     RowStatus
-- MAX-ACCESS  read-create
   MAX-ACCESS  read-only
   STATUS     current
   DESCRIPTION
       "An object that allows entries in this table to
       be created and deleted using the
       RowStatus convention."
   ::= { jnxMplsLdpLspFecEntry 3 }


--
-- Address Message/Address Withdraw Message Information
--
-- This information is associated with a specific Session
-- because Label Address Messages are sent after session
-- initialization has taken place.
--

jnxMplsLdpSesPeerAddrTable OBJECT-TYPE

    SYNTAX      SEQUENCE OF JnxMplsLdpSesPeerAddrEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "This table 'extends' the jnxMplsLdpSessionTable.
        This table is used to store Label Address Information
        from Label Address Messages received by this LSR from
        Peers.  This table is read-only and should be updated
        when Label Withdraw Address Messages are received, i.e.
        Rows should be deleted as apropriate.

        NOTE:  since more than one address may be contained
        in a Label Address Message, this table 'extends',
        rather than 'AUGMENTS' the jnxMplsLdpSessionTable's
        information."
    ::= { jnxMplsLdpSessionObjects 9 }

jnxMplsLdpSesPeerAddrEntry OBJECT-TYPE
    SYNTAX      JnxMplsLdpSesPeerAddrEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry in this table represents information on
        session's for a single next hop address which was
        advertised in an Address Message from the LDP peer.
        The information contained in a row is read-only."
    INDEX       { jnxMplsLdpEntityLdpId,
                  jnxMplsLdpEntityIndex,
                  jnxMplsLdpPeerLdpId,
                  jnxMplsLdpSesPeerAddrIndex
                }
    ::= { jnxMplsLdpSesPeerAddrTable 1 }

JnxMplsLdpSesPeerAddrEntry ::= SEQUENCE {
    jnxMplsLdpSesPeerAddrIndex       Unsigned32,
    jnxMplsLdpSesPeerNextHopAddrType InetAddressType,
    jnxMplsLdpSesPeerNextHopAddr     InetAddress
}

jnxMplsLdpSesPeerAddrIndex OBJECT-TYPE
    SYNTAX      Unsigned32 (1..4294967295)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An index which uniquely identifies this entry within
        a given session."
    ::= { jnxMplsLdpSesPeerAddrEntry 1 }

jnxMplsLdpSesPeerNextHopAddrType OBJECT-TYPE
    SYNTAX      InetAddressType

    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The internetwork layer address type of this Next Hop
        Address as specified in the Label Address Message
        associated with this Session. The value of this
        object indicates how to interpret the value of
        jnxMplsLdpSessionPeerNextHopAddress."
    ::= { jnxMplsLdpSesPeerAddrEntry 2 }

jnxMplsLdpSesPeerNextHopAddr OBJECT-TYPE
    SYNTAX      InetAddress
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The value of the next hop address."
    REFERENCE
        "[RFC3036], LDP Specification defines only IPv4 for
        LDP Protocol Version 1, see section 3.4.3."
    ::= { jnxMplsLdpSesPeerAddrEntry 3 }


---
--- Notifications
---

jnxMplsLdpNotificationPrefix   OBJECT IDENTIFIER ::=
                                 { jnxMplsLdpNotifications 0 }

jnxMplsLdpInitSesThresholdExceeded NOTIFICATION-TYPE
     OBJECTS     {
                   jnxMplsLdpEntityInitSesThreshold
                 }
     STATUS      current
     DESCRIPTION
        "This notification is generated when the value of
        the 'jnxMplsLdpEntityInitSesThreshold' object
        is not zero, and the number of Session
        Initialization messages exceeds the value
        of the 'jnxMplsLdpEntityInitSesThreshold' object."
     ::= { jnxMplsLdpNotificationPrefix 1 }

jnxMplsLdpPathVectorLimitMismatch NOTIFICATION-TYPE
     OBJECTS     {
                   jnxMplsLdpEntityPathVectorLimit,
                   jnxMplsLdpPeerPathVectorLimit
                 }
     STATUS      current
     DESCRIPTION
        "If this notification is enabled to generated,

        then this notification is sent when the
        'jnxMplsLdpEntityPathVectorLimit' does NOT match
        the value of the 'jnxMplsLdpPeerPathVectorLimit' for
        a specific Entity."
     REFERENCE
        "[RFC3036], LDP Specification, Section 3.5.3."
     ::= { jnxMplsLdpNotificationPrefix 2 }

jnxMplsLdpSessionUp NOTIFICATION-TYPE
     OBJECTS     {
                    jnxMplsLdpSesState,
                    jnxMplsLdpSesDiscontinuityTime,
                    jnxMplsLdpSesStatsUnkMesTypeErrors,
                    jnxMplsLdpSesStatsUnkTlvErrors
                 }
     STATUS      current
     DESCRIPTION
        "If this notification is enabled to generated,
        then this notification is sent when the
        value of 'jnxMplsLdpSesState' enters
        the 'operational(5)' state."
     ::= { jnxMplsLdpNotificationPrefix 3 }

jnxMplsLdpSessionDown NOTIFICATION-TYPE
     OBJECTS     {
                    jnxMplsLdpSesState,
                    jnxMplsLdpSesDiscontinuityTime,
                    jnxMplsLdpSesStatsUnkMesTypeErrors,
                    jnxMplsLdpSesStatsUnkTlvErrors

                 }
     STATUS      current
     DESCRIPTION
        "If this notification is enabled to generated,
        then this notification is sent when the
        the value of 'jnxMplsLdpSesState' leaves
        the 'operational(5)' state."
     ::= { jnxMplsLdpNotificationPrefix 4 }


--****************************************************************
-- Module Conformance Statement
--****************************************************************


jnxMplsLdpGroups
    OBJECT IDENTIFIER ::= { jnxMplsLdpConformance 1 }

jnxMplsLdpCompliances
    OBJECT IDENTIFIER ::= { jnxMplsLdpConformance 2 }

--
-- Full Compliance
--

jnxMplsLdpModuleFullCompliance MODULE-COMPLIANCE
    STATUS current
    DESCRIPTION
        "The Module is implemented with support
        for read-create and read-write.  In other
        words, both monitoring and configuration
        are available when using this MODULE-COMPLIANCE."

    MODULE -- this module
        MANDATORY-GROUPS    { jnxMplsLdpGeneralGroup,
                              jnxMplsLdpLspGroup,
                              jnxMplsLdpNotificationsGroup
                            }


    GROUP jnxMplsLdpLsrGroup
    DESCRIPTION
        "This group must be supported if the LSR MIB is
        implemented, specifically the mplsInSegmentTable,
        the mplsOutSegmentTable or the mplsXCTable."

    OBJECT jnxMplsLdpEntityTargetPeerAddrType
    SYNTAX InetAddressType 
    DESCRIPTION
       "An implementation is only required to support
       'unknown(0)', and IPv4 addresses. Supporting
       IPv6 addresses is optional."


    OBJECT jnxMplsLdpEntityTargetPeerAddr
    SYNTAX InetAddress (SIZE(0|4|16))
    DESCRIPTION
        "An implementation is only required to support IPv4 and
        may optionally support IPv6 addresses."

    OBJECT jnxMplsLdpEntityRowStatus
    SYNTAX INTEGER { active(1) } 
    WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) }
    DESCRIPTION
        "Support for createAndWait and notInService is not
        required."

    OBJECT jnxMplsFecAddrFamily
    SYNTAX InetAddressType 
    DESCRIPTION
       "An implementation is only required to support

       'unknown(0)', and IPv4 addresses. Supporting
       IPv6 addresses is optional."

    OBJECT jnxMplsFecAddr
    SYNTAX InetAddress (SIZE(0|4|16))
    DESCRIPTION
        "An implementation is only required to support IPv4 and
        may optionally support IPv6 addresses."

    OBJECT jnxMplsFecRowStatus
    SYNTAX INTEGER { active(1) }
    WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) }
    MIN-ACCESS   read-only
    DESCRIPTION
        "Support for createAndWait and notInService is not
        required. Also, the entries in this table may be
        created by the agent, so strictly speaking
        read-create functionality is not necessary, but
        may be nice to have."

    OBJECT jnxMplsLdpLspFecRowStatus
    SYNTAX INTEGER { active(1) }
    WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) }
    MIN-ACCESS   read-only
    DESCRIPTION
        "Support for createAndWait and notInService is not
        required. Also, the entries in this table may be
        created by the agent, so strictly speaking
        read-create functionality is not necessary, but
        may be nice to have."

    OBJECT jnxMplsLdpSesPeerNextHopAddrType
    SYNTAX InetAddressType
    DESCRIPTION
        "An implementation is only required to support
        'unknown(0)', and IPv4 addresses. Supporting
        IPv6 addresses is optional."

    OBJECT jnxMplsLdpSesPeerNextHopAddr
    SYNTAX InetAddress (SIZE(0|4|16))
    DESCRIPTION
        "An implementation is only required to support IPv4
        and may optionally support IPv6 addresses."


    ::= { jnxMplsLdpCompliances 1 }

--
-- Read-Only Compliance
--

jnxMplsLdpModuleReadOnlyCompliance MODULE-COMPLIANCE
    STATUS current
    DESCRIPTION
        "The Module is implemented with support
        for read-only.  In other words, only monitoring
        is available by implementing this MODULE-COMPLIANCE."

    MODULE -- this module
        MANDATORY-GROUPS    { jnxMplsLdpGeneralGroup,
                              jnxMplsLdpLspGroup,
                              jnxMplsLdpNotificationsGroup
                            }


    GROUP jnxMplsLdpLsrGroup
    DESCRIPTION
        "This group must be supported if the LSR MIB is
        implemented, specifically the mplsInSegmentTable,
        the mplsOutSegmentTable or the mplsXCTable."

    OBJECT       jnxMplsLdpEntityProtocolVersion
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityAdminStatus
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityTcpDscPort
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityUdpDscPort
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityMaxPduLength
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityKeepAliveHoldTimer
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityHelloHoldTimer
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityInitSesThreshold
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityLabelDistMethod
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityLabelRetentionMode
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityPathVectorLimit
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityHopCountLimit
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityTargetPeer
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityTargetPeerAddrType
    SYNTAX       InetAddressType 
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required.
       An implementation is only required to support
       'unknown(0)', and IPv4 addresses. Supporting
       IPv6 addresses is optional."

    OBJECT       jnxMplsLdpEntityTargetPeerAddr
    SYNTAX       InetAddress (SIZE(0|4|16))
    MIN-ACCESS   read-only
    DESCRIPTION
        "Write access is not required.
        An implementation is only required to support IPv4 and

        may optionally support IPv6 addresses."

    OBJECT       jnxMplsLdpEntityLabelType
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsLdpEntityStorageType
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT jnxMplsLdpEntityRowStatus
    SYNTAX INTEGER { active(1) }
    MIN-ACCESS   read-only
    DESCRIPTION
        "Write access is not required, and active is the
        only status that needs to be supported."

    OBJECT       jnxMplsFecType
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsFecAddrLength
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT       jnxMplsFecAddrFamily
    SYNTAX       InetAddressType 
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required.
       An implementation is only required to support
       'unknown(0)', and IPv4 addresses. Supporting
       IPv6 addresses is optional."

    OBJECT        jnxMplsFecAddr
    SYNTAX        InetAddress (SIZE(0|4|16))
    MIN-ACCESS    read-only
    DESCRIPTION
        "Write access is not required.
        An implementation is only required to support IPv4 and
        may optionally support IPv6 addresses."

    OBJECT       jnxMplsFecStorageType
    MIN-ACCESS   read-only
    DESCRIPTION
       "Write access is not required."

    OBJECT jnxMplsFecRowStatus
    SYNTAX INTEGER { active(1) }
    MIN-ACCESS   read-only
    DESCRIPTION
        "Write access is not required, and active is the
        only status that needs to be supported."

    OBJECT jnxMplsLdpLspFecRowStatus
    SYNTAX INTEGER { active(1) }
    MIN-ACCESS   read-only
    DESCRIPTION
        "Write access is not required, and active is the
        only status that needs to be supported."

    OBJECT jnxMplsLdpSesPeerNextHopAddrType
    SYNTAX InetAddressType 
    DESCRIPTION
       "An implementation is only required to support
       'unknown(0)', and IPv4 addresses. Supporting
       IPv6 addresses is optional."


    OBJECT jnxMplsLdpSesPeerNextHopAddr
    SYNTAX InetAddress (SIZE(0|4|16))
    DESCRIPTION
        "An implementation is only required to support IPv4
        and may optionally support IPv6 addresses."

    ::= { jnxMplsLdpCompliances 2 }


-- units of conformance

jnxMplsLdpGeneralGroup OBJECT-GROUP
    OBJECTS {
    jnxMplsLdpLsrId,
    jnxMplsLdpLsrLoopDetectionCapable,
    jnxMplsLdpEntityLastChange,
    jnxMplsLdpEntityIndexNext,
    jnxMplsLdpEntityProtocolVersion,
    jnxMplsLdpEntityAdminStatus,
    jnxMplsLdpEntityOperStatus,
    jnxMplsLdpEntityTcpDscPort,
    jnxMplsLdpEntityUdpDscPort,
    jnxMplsLdpEntityMaxPduLength,
    jnxMplsLdpEntityKeepAliveHoldTimer,
    jnxMplsLdpEntityHelloHoldTimer,
    jnxMplsLdpEntityInitSesThreshold,
    jnxMplsLdpEntityLabelDistMethod,
    jnxMplsLdpEntityLabelRetentionMode,

    jnxMplsLdpEntityPathVectorLimit,
    jnxMplsLdpEntityHopCountLimit,
    jnxMplsLdpEntityTargetPeer,
    jnxMplsLdpEntityTargetPeerAddrType,
    jnxMplsLdpEntityTargetPeerAddr,
    jnxMplsLdpEntityLabelType,
    jnxMplsLdpEntityDiscontinuityTime,
    jnxMplsLdpEntityStorageType,
    jnxMplsLdpEntityRowStatus,
    jnxMplsLdpAttemptedSessions,
    jnxMplsLdpSesRejectedNoHelloErrors,
    jnxMplsLdpSesRejectedAdErrors,
    jnxMplsLdpSesRejectedMaxPduErrors,
    jnxMplsLdpSesRejectedLRErrors,
    jnxMplsLdpBadLdpIdentifierErrors,
    jnxMplsLdpBadPduLengthErrors,
    jnxMplsLdpBadMessageLengthErrors,
    jnxMplsLdpBadTlvLengthErrors,
    jnxMplsLdpMalformedTlvValueErrors,
    jnxMplsLdpKeepAliveTimerExpErrors,
    jnxMplsLdpShutdownNotifReceived,
    jnxMplsLdpShutdownNotifSent,
    jnxMplsLdpPeerLastChange,
    jnxMplsLdpPeerLabelDistMethod,
    jnxMplsLdpPeerPathVectorLimit,
    jnxMplsLdpHelloAdjHoldTimeRem,
    jnxMplsLdpHelloAdjType,
    jnxMplsLdpSesStateLastChange,
    jnxMplsLdpSesState,
    jnxMplsLdpSesProtocolVersion,
    jnxMplsLdpSesKeepAliveHoldTimeRem,
    jnxMplsLdpSesMaxPduLength,
    jnxMplsLdpSesDiscontinuityTime,
    jnxMplsLdpSesStatsUnkMesTypeErrors,
    jnxMplsLdpSesStatsUnkTlvErrors,
    jnxMplsLdpSesPeerNextHopAddrType,
    jnxMplsLdpSesPeerNextHopAddr,
    jnxMplsFecIndexNext,
    jnxMplsFecType,
    jnxMplsFecAddrFamily,
    jnxMplsFecAddrLength,
    jnxMplsFecAddr,
    jnxMplsFecStorageType,
    jnxMplsFecRowStatus,
    jnxMplsLdpLspFecOperStatus,
    jnxMplsLdpLspFecLastChange,
    jnxMplsLdpLspFecRowStatus
    }
    STATUS    current
    DESCRIPTION

        "Objects that apply to all MPLS LDP implementations."
    ::= { jnxMplsLdpGroups 1 }


jnxMplsLdpLspGroup OBJECT-GROUP
    OBJECTS {
    jnxMplsLdpLspLabelType,
    jnxMplsLdpLspType
    }
    STATUS    current
    DESCRIPTION
        "These objects are specific to LDP LSPs."
    ::= { jnxMplsLdpGroups 2 }

jnxMplsLdpLsrGroup OBJECT-GROUP
    OBJECTS {
    jnxMplsLdpLspLsrInSegmentPointer,
    jnxMplsLdpLspLsrOutSegmentPointer,
    jnxMplsLdpLspLsrXCPointer
    }
    STATUS    current
    DESCRIPTION
        "These objects are optional and only need to be supported
        for LDP implementations which support the following
        tables in the LSR MIB: mplsInSegmentTable,
        mplsOutSegmentTable and mplsXCTable."
    ::= { jnxMplsLdpGroups 3 }


jnxMplsLdpNotificationsGroup NOTIFICATION-GROUP
    NOTIFICATIONS { jnxMplsLdpInitSesThresholdExceeded,
                    jnxMplsLdpPathVectorLimitMismatch,
                    jnxMplsLdpSessionUp,
                    jnxMplsLdpSessionDown
                       }
    STATUS   current
    DESCRIPTION
        "The notification(s) which an MPLS LDP implemention
         is required to implement."
    ::= { jnxMplsLdpGroups 4 }


END